Firmware For Huawei Hg633 Router 2019
Not supported
- Huawei Hg633 Firmware Update Download
- Huawei Hg633 Router Firmware
- Huawei Hg633 Firmware Update
- Firmware For Huawei Hg633 Router 2019
Forum: https://forum.openwrt.org/viewtopic.php?id=55856
Source code: hg635-opensource.tar.gz
Installation
Flashing ANY Firmware
Firmware HUAWEI MODEM HG633-12. Firmware HUAWEI MODEM HG658d-10. Firmware HUAWEI MODEM HG659-12. This is an example to configure the switch: numbers 0-2 will be lan, labeled as Ports LAN1X, LAN2X, LAN3X on the unit, number 3 (LAN4X) will be the Internet (WAN), 8 is the internal connection to the router itself. Don't be fooled: vlan1 = eth0.1, vlan2 = eth0.2 and so on. This is an example to configure the switch: numbers 0-2 will be lan, labeled as Ports LAN1X, LAN2X, LAN3X on the unit, number 3 (LAN4X) will be the Internet (WAN), 8 is the internal connection to the router itself.Don't be fooled: vlan1 = eth0.1, vlan2 = eth0.2 and so on.
You must set your TCP/IP v4 protocol at your computer to:
- Netmask: 255.255.255.0
- DNS: (optional, can be blank).
Then:
- Press reset button near the antenna.
- Keep it pressed while powering up during ~20+ seconds.
- Acces to http://192.168.1.1 and upload binary file.
Specific Configuration
Interfaces
The default network configuration is:
| Interface Name | Description | Default configuration |
|---|---|---|
| br-lan | LAN & WiFi | 192.168.1.1/24 |
| eth0.1 | LAN ports (1 to 4) | bridged |
| eth0.2 | WAN port (WAN) | nat (WAN) |
| wlan0 | WiFi | bridged (disabled) |
| wlan1 | WiFi | bridged (disabled) |
Switch Ports (for VLANs)
This is an example to configure the switch: numbers 0-2 will be lan, labeled as Ports LAN1X, LAN2X, LAN3X on the unit, number 3 (LAN4X) will be the Internet (WAN), 8 is the internal connection to the router itself. Don't be fooled: vlan1 = eth0.1, vlan2 = eth0.2 and so on.
| Port | Switch port | Mode |
|---|---|---|
| 1 | 0 | lan |
| 2 | 1 | lan |
| 3 | 2 | lan |
| 4 | 3 | lan |
| WAN | 4 | Internet (WAN) |
| n/a | 5t | to CPU |
Hardware
Info
| Instruction set | MIPS |
|---|---|
| Vendor | Broadcom |
| bootloader | cfe |
| Board ID | |
| System-On-Chip | Broadcom BCM63168 |
| CPU @Frq | BMIPS4350 V8.0 @ 400 MHz |
| Flash-Chip | NAND |
| Flash size | 128MB |
| RAM-Chip | DDR2-800 |
| RAM size | 128MB |
| Wireless | BCM4350 ac/a/b/g/n (onboard) + BCM6362 b/g/n (SoC) |
| Ethernet | BCM53124, 5x 1000M |
| USB | 1x 2.0 |
| Serial | Yes |
| JTAG | ? |
Photos
Opening the case
Note: This will void your warranty!
Huawei Hg633 Firmware Update Download
Main PCB:
JTAG
→ port.jtag general information about the JTAG port, JTAG cable, etc.
N/A
Serial
Huawei Hg633 Router Firmware
→ port.serial general information about the serial port, serial port cable, etc.
How to connect to the Serial Port of this specific device:
Serial port settings 115200, 8N1
Pinout:
J5002
1 - RXD
2 -
3 - Probably VCC (3V3)
4 - GND
5 - TXD
Photo of PCB with markings
GPIO
LEDs
Read: System configuration: Leds to configure the leds
Buttons
→ hardware.button on howto use and configure the hardware button(s).
Bootlogs
OEM Bootlog
Huawei Hg633 Firmware Update
HELO CPUI L1CI HELO CPUI L1CI DRAM ---- PHYS STRF 400H PHYE DDR3 SIZ4 SIZ3 SIZ2 DINT USYN LSYN MFAS LMBE RACE PASS ---- ZBSS CODE DATA L12F MAIN CFE version 1.0.38-114.174 for BCM963268 (32bit,SP,BE)Build Date: Sat Nov 9 13:59:00 CST 2013 (l00184769@localhost)Copyright (C) 2000-2011 Broadcom Corporation.NAND flash device: name , id 0x98d1 block 128KB size 131072KBExternal switch id = 53125 Chip ID: BCM63168D0, MIPS: 400MHz, DDR: 400MHz, Bus: 200MHz Main Thread: TP0 Memory Test Passed Total Memory: 134217728 bytes (128MB) Boot Address: 0xb8000000